Видео

Do you have any insight as to why my contacter gets hot and smokes after 5 minutes? I’ve rechecked my wiring and the vfd seems to work fine. The contacter will eventually get too hot and pop and my second one is doing it too. I’ve ordered everything from your provided links. Could it be poor quality parts?

Going to bring another give away ? 😅. I’m thinking to buy one of those ultimate setup

Interesting, I was watching harbor freight welding table but it’s $30 more expensive

The autozone loan a tool 57000 will work. Then you need M5 and m6 bolts.

Just got them for 16.99

Ignorant people will always coment Ignorant opinions great video guy good luck God bless

Great video, thanks for the help

The kit is designed to be used with a new bumper with factory made cutout.

0:05 Awesome Spinal Tap reference: "THESE GO TO ELEVEN" !!! 😂😂😂 Making 10 louder will never be the same as cranking up to 11. 😜

Why didn't you just use the control panel from the oven?

What is that piece made of, that you placed in the hole to do the final weld on the nut.

Where is the link on the p.i.d. programing

Hey man awesome video! Have you done the wiring yet? If so did you go oem wiring or like curt brand wiring. If so how did you do the 4 pin end. Did it fit into the hitch bracket or just hanging?

Do you have a filter made for the shifter portion on the gauge for automatic cars?

Thanks for the link to the motor. I'm going to try the 20 rpm for TIG welding. I found the speed as a flaw also. What were they thinking??

Thank you so much , I'm trying to restore a 65 IH Scout and you just showed me how to remove the spot welds. Thanks again

This magician must work for Milwaukee

Beautiful product. I was all set on buying the cheaper usa version on ebay (guy in texas) but I may hold out and spend the extra for yours. Does your DIY builder version have the long lead time as well? Also as someone that does fabrication on the side, I totally understand the price point of your kit!

Please sell the kit or do this service we would happily pay for iy

Could you changes tyre with off road tyre pls...

I want to buy one..

Why you didnt filled it up with concrete or sand?

Can this be done on a walmart hyper tough 3/8" impact? I'm even cheaper and wanted to convert the anvil to 1/4".

Probably meant prefill the filter itself

How can 1 get this manual tire changer? From medan, Indonesia

Were I can faun the kit can you tell me please

how did you bench test this?I have one that I want to sell but don't know how to check milage oranythiung and can't find anything on line how to do it haha

People in Ireland buy them if they are on sale but in not in shop to buy them at moment

As a 34yr professional commercial tire guy. Advice: Get yourself a tyreguy friend. World works on,"I know a guy"

I bought this unit and did not get the clip and carbon brush to allow the unit to give the ability to use the turntable for Welding. I've contacted vevor about this and am getting the runaround. They said it's a consumable they drop $60 off, and I then needed to find the brush and clip. I said no way either send the part or give me a return label and a full refund. I wouldn't have any idea where to buy the part and I'm assuming by there reply they don't offer replacement parts rendering it worthless in time. Bad business practice.

Can you change ATV tires with this?

Awesome thank man

These small ones are rated up to 80 amps. That’s it! I’ve got a similar one, not from Vevor. I think it cost me, around 18 months ago, $325. Prices have dropped to about $263 now. I’ve gone to 120 amps and it’s been ok, but I wouldn’t go higher than that. Mine does have a reverse switch. I’m thinking of going to the next larger size.

Hopefully you see this I’m a little late lol. Something I’ve noticed across all tool brands especially Milwaukee is that there is always a massive price difference between a hex and anvil (driver and wrench). So I have a couple questions, 1: how has the performance been with the modified 2nd gen (I don’t think there is a 3rd gen impact wrench yet)? Have you been able to compare it to the hex impact in terms of performance? And how does it hold up to buying the purpose built impact wrench? Not sure if that’s possible for you or not. 2: is there a hammer/internal difference between the wrench and driver? Usually there’s some small machining differences etc, but I’ve noticed that these are just plug and play swaps. I’m just morbidly curious if they are just the same exact M12 tool, hammer and everything, just with different anvils and charging more for the wrench which I still dont understand. I might be a little more understanding if the hammer assemblies were different to compliment the hardware like on some tools I’ve disassembled but from what I’ve seen I don’t see any visual differences. Maybe the weight of the hammer? I got to know haha. Sorry for long post, thanks for any feedback and sweet vid!!! I’ll probably be doing this with a gen three here soon.

Great video, thanks for sharing your knowledge 👍.

Can't believe that factory part didn't come with those side clips. My guess is whoever was building up those kits didn't include the clips.

Just ordered my part! Thanks!

where did you place the thermal coupler?

Can this be done on a Surge?

Could this be used to remove bonded on side skirts...I believe it's similar adhesive.

I ended up breaking the little selector knob on the trigger when reassembling is there an option to purchase a replacement trigger that anyone knows of?

If you had help it would have gone faster

good job

Is there a limit to tyre profile it can handle? Like 205/40 17 or other tyres with a wall height of only 80mm or so? (roughly 3 inches)

Sorry.. I think it's waist of time It will damage the rims

If you take valve cores out, it will be much easier to push tool under lip of wheels

I want to buy one

Ok I have a stupid question, how do you pick what size hole saw do you buy ? I would imagine if you have 1 3/4” pipe that is the size saw you want is that correct ?

Does this also work on aluminium and steel blanks

can i just leave th efilters out to make it white? (for the lcd's)